Kit Cafe Racer

BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit

BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit
BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit

BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit    BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit

FlatRacer BMW R2v Airhead Boxer R90S R100S & R100CS replica cockpit fairing - PARTIAL kit. This FlatRacer BMW R90S replica cockpit fairing kit is designed to fit any BMW R2v /6 and /7 Series and to be as near bolt on as possible, following closely the original design. Suits bike models already fitted with the original pressed steel headlight pegs and the long type indicator stalks and associated fittings, specific to the S/CS models. FR BMW R90S replica cockpit fairing - fibreglass faithful replica, stronger than the crack prone originals. BMW OEM fairing/headlight rubber seal.

BMW OEM black plastic cockpit dash. FR BMW R90S clear screen - standard size - pre-drilled.

11 x M4 s/s screen csk bolts, conical s/s washers, s/s small M4 penny washers + nyloc nuts + rubber spacers. FR BMW R90S cockpit fairing inner s/s small angled brackets (pair) + required s/s M6 fasteners. BMW R90 cockpit fairing small rubber grommets (pair) for angle brackets + s/s bushes. FR BMW R90S cockpit fairing tubular s/s brackets (pair) + required s/s M6 fasteners. FR BMW R90S cockpit fairing yoke mounted flat s/s brackets (pair) + required s/s M6 fasteners. Stainless steel M6 long bolts + washers & nyloc nuts - locate the flat brackets on the yoke plate. Our fairing is very sturdy, thick (typically between 4 to 6mm), it will not flex or shake at speed. Very well finished with a fairly smooth surface inside (we apply a final GRP surface mat for a better finish) with out usual attention to details so no air bubbles, cracks, frayed edges etc. Minimal preparation work is required prior to painting. Our fairing follows very closely the lines of the original fairing unlike most replicas on the market. All the parts are pre-drilled, pre-trimmed and pre-mated so very little preparation work is required to fit apart from painting.

We've adopted the original inner fairing fastening set up, albeit using nylon lugs with a captive M6 brass nuts. A refined solution rarely adopted due to the complexity and extra labour required. Our fairing is much stronger than the original fairing assembly, notorious for their fragility and propensity to crack (injected fibreglass filament chopped strands with plaster type material). Originally the screen was riveted to the fairing/dash using a special setting tool, requiring specific (and expensive) brass bushes and plastic rivets.

Although quite neat, it was not a practical solution if the screen or dash needed to be removed for replacement or fairing repair. We've replaced these items with our own stainless steel M4 csk bolts and some very neat and elegant s/s conical cup washers plus penny washers to spread the load, rubber washers to reduce vibrations and abrasions and nyloc nuts for a secure screen fitting. We include an extra fastener to keep as a spare in case you loose any of the fiddly items. This kit is the most complete you will find and does includes a stainless steel upper fitting kit (close replicas of the original items) to fit this fairing to an original R90S, /6 or the later /7 Series already fitted with the original headlight pegs, S type long indicators stalks and associated fittings. Outstanding period look, sturdiness, quality and durability.

This kit will fit the BMW R90S, R100S, R100 CS and all /6 & /7 Series (73-84) fitted with the original 36mm fork stanchions and low rise handlebar. 1 - This fairing requires the use of low rise handlebars, as fitted to the R90S. If fitted to a post 1981 bike or fitted with a bar mounted brake master cylinder, further adjustments may be required for it to clear the fairing.

2 - In order to fit this fairing to a BMW, you will need to use the original pressed steel headlight pegs and the long indicator stalks and associated fittings that work as lower mounts, s. Pecific to the S/CS model. We can supply original headlight pegs, indicator stalks and associated lower fittings, indicators, dash stickers, voltmeter and clock + sub-loom etc, etc. Similar kit available for the Monolever (post 1985) models. We can also supply very nice replicas of the original clamp on stem plastic indicators, suitable for this fairing.

We can also supply a R90S type or the later /7 polished stainless steel top yoke plate (4mm thick) and other components to tidy up the top yoke are such as our FR s/s steering top centre nut and fork pre-load adjusters (handlebar adjustments may be required). The item "BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit" is in sale since Sunday, August 25, 2019. This item is in the category "Vehicle Parts & Accessories\Motorcycle Parts\Suspension & Handling\Fork Yokes". The seller is "flatracer1" and is located in London. This item can be shipped worldwide.

  • Country/Region of Manufacture: United Kingdom
  • Machine Type: BMW R90S
  • Unit Quantity: 1 kit
  • Classic Motorcycle Part: Yes
  • Manufacturer Part Number: Does Not Apply
  • Brand: FlatRacer
  • Intended Use: Performance Part


BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit    BMW R90S R100S R100CS Cafe Racer S cockpit fairing PARTIAL kit